Vertical Roof Garage 22W x 41L x 12H
22' Wide x 41' Long x 12' High Garage with Vertical Roof System.
As a General Rule, these are the options available for our service area state. Check with your local permitting office for their specific requirements, if any.
14 Gauge Non-Certified/Non-Rated Units for 12' Wide to 24' Wide Units and Barn Units
12 Gauge Non-Certified/Non-Rated Units for 12’ Wide to 24’ Wide Units and Barn Units
14 Gauge Engineer Certified for 130 MPH/30PSF for 12' Wide to 24' Wide Units and Barn Units
12 Gauge Engineer Certified for 130 MPH/30 PSF for 12’ Wide to 24’ Wide Units and Barn Units
14 Gauge Engineer Certified 130 MPH/30 PSF for 26’ Wide to 30’ Wide Units
12 Gauge Engineer Certified 130 MPH/30 PSF for 26’ Wide to 30’ Wide Units
12 Gauge Engineer Certified for 130 MPH/60 PSF for 26’ Wide to 30’ Wide Units
14 Gauge Engineer Certified for 130 MPH/30 PSF for 32’ Wide to 40’ Wide Units
12 Gauge Engineer Certified for 130 MPH/30 PSF for 32’ Wide to 40’ Wide Units
Delivery and Installation are FREE as long as your site is level, has no obstructions, and it is within 50' of our installation crew's vehicle and trailer.
For best results, the installation site should be as level as possible. Here are some general guides:
- We can work with a site that is 3" to 4" off-level.
- For sites 4" to 12" off-level, there is a labor fee to level the site or cut the legs on site. Call for details.
- For sites that are more than 12" out of level, we cannot install the unit because the unit will be unstable.
For Garage and Barns:
- For best results, your site to be level!
- We can work with a site that is 2-4" off level but the unit will perform better if the site is level. Garage doors operate and perform well when the site is level. Side and end wall panels alignment is best with a level site.
Installation crews can install all of the units on the ground (grass, dirt, gravel, crusher run, asphalt) and concrete pads. We can install units on a non-floating wood deck for an extra charge. Engineer certified units cannot be installed on a wood deck.
For installation contractor's safety, we DO NOT install units on floating boat docks. We can drop off the unit so that you or your contractor can install the unit.
We can install units on a raised concrete wall for an extra charge. The wall height can be no greater than 3' tall. The total side height of unit can be no taller than 14'. Please call for pricing.
|Back End Wall||Fully Enclosed|
|Front End Wall||Fully Enclosed with (1) 10'W x 10'H Garage Door|
|Left Side Wall||Fully Enclosed with (3) 10'W x 10' H Garage Doors|
|Right Side Wall||Fully Enclosed|
|Roof Panel Corrugated Ridge Orientation||Vertical - Up and Down|
|Roof System||Vertical Roof|
In addition to providing the best carports in Sealy, TX and in surrounding cities in Austin county, we also provide RV shelters, enclosed metal garages, prefabricated metal buildings, barns, and workshops to San Antonio, TX, Houston, TX, Corpus Christi, TX, Austin, TX, Katy, TX, Rosenberg, TX, Richmond, TX, San Filipe, TX, Frydek, TX, Rexville, TX, Peters, TX, Clemons, TX and other cities and communities in the Lone Star State. Customers in the area love our durable steel structures, which feature a 14 gauge or optional 12 gauge galvanized, tubular steel frame that is rot, fire, and pest resistant. Our 29 gauge galvanized steel panels can handle the varied Texas heat and storms. We also have a heavier 26 gauge option for those customers that want a more durable exterior steel panel. Both non-certified and engineer certified (rated for wind and snow) are available in widths up to 24'. All units wider than 24' are engineer certified. If your area's building inspections department requires a building permit, you would need an engineer certified unit. We offer widths from 12' wide to 40' wide and side heights up to 14'. For steel buildings and structures that are fully enclosed, we offer roll-up doors in a variety of widths and heights, as well as personnel/walk-in doors, and windows.
Ordering Metal Carports for Sealy, TX 77474
Getting a metal building from C&H Carports is simple and easy. Most customers visit one of our knowledgeable carport dealer representatives to place their order. Their staff will work with you to ensure that you get the right car port, enclosed garage, barn, or other building that you need. Those dealers can provide you with the most current carport prices and options. Once you have selected the unit that you need, the dealer collect a small down payment to get your order started and they will forward your order to our East Texas manufacturing. The staff at C&H Carports will contact you to ensure that your order is to your specification and once that is confirmed, we will begin the manufacturing process. We build the unit in our plant using efficient modular manufacturing methods and we inspect each process that you receive the highest quality unit. Once the unit is built to your specifications, we contact you to schedule delivery and installation. Almost always, from start of order to installation, it usually take from two to four weeks. We do experience higher demands and certain times of the year. For detailed information and the most accurate installation lead times, contact your C & H Carports dealer or contact us directly.
Installation and Delivery
On the day of installation, the crew will arrive to install your unit. Generally, we schedule for morning, mid-day or afternoon. We don't specify and exact time as weather or other unexpected conditions may impede the crew's progress. The job site should be free from obstructions (unless pre-approved in advance), should have no overhead utility lines within 12' of the site, and no underground utilities lines, unless they are well marked. The crew will begin to erect your structure. Installation is usually quick and efficient because of the modular construction methods used. As always, please call us for additional questions and assistance.